2018s new design compression docking wastes collecting vehic
Release time:2018-07-25 14:33 Editor:
truckdf From:Chengli
2018s new design compression docking wastes collecting vehicle for sale
Multi-functional compression butt joint garbage truck,also called Docking garbage truck, compressed docking wastes collecting vehicle and known as garbage compression station docking garbage truck: is used in urban refuse compression station garbage transfer, unloading operation of the special vehicle.
The working principles of CLW brand 5m3 compression docking wastes collecting vehicle as below
The vehicle operating system is a hydraulic control system to complete, the control mode can be manual or electrical control. The garbage bin is compressed into pieces and the garbage box is lifted vertically, and open the cabinet drain door, when the garbage truck box back up to rotate open, garbage truck back door with the compression box back docking, after the garbage block is compressed box of the push plate level into the body of the garbage truck, complete garbage loaded after the garbage truck back door, The rubbish is transported to the disposal place for dumping.
More pictures of Dongfeng compression docking wastes collecting vehicle as below
customized CLW Brand 5m3 compression docking garbage truck for sale
HOT SALE! new design wastes collecting vehicle for sale
main technical parameters of Dongfeng 5m3 compression docking garbage truck manufactured by Chengli Special Automobile Co., Ltd.
New designed CLW brand 5m3 Compression docking garbage truck(CLW5071ZDJT5) |
Truck model |
CLW5071ZDJT5 Compression docking garbage truck |
Remark |
Chassis model |
EQ1060 |
|
Wheelbase |
3300 mm |
|
Front/rear suspension |
1070/1310,1070/1200 mm |
|
Engine model |
CY4102 |
|
Engine rated power |
86;85 kW |
|
Max climbing angle |
30% |
|
Emission standard |
GB17691-2005 Euro Ⅲ,GB3847-2005 |
|
Acceleration of external noise |
≤84dB(A), |
|
Max speed |
90 km/h |
|
Approach/departure angle |
24° |
|
Departure angle |
12° |
|
Mass |
Curb mass |
4500 kg |
|
Max total mass |
7350 kg |
|
Dimension |
Overall dimension(L*W*H) |
5570×1960×2700 mm |
|
Mini ground clearance |
240 mm |
|
Wastes box volume |
5m³ |
|
Working time |
Loading |
15~18 s |
|
Shirking |
22~24 s |
|
compressing |
18~20 s |
|
Hydraulic system |
rated pressure |
16 MPa |
|
Oil cylinders |
China made |
|
The technical advantages of nee designed CLW Brand compression docking garbage truck as below
1, the sliding structure of the push plate is with s groove track on both sides; comparing to the track placed on the floor of the truck, this kind of structure with the advantages of high rigidity, good stability, no deformation of the bottom plate, smooth movement of the push plate, clean waste discharge and reliable work, etc.
2,The van box body of the wastes collecting truck is made of high-strength weather-resistant steel, and the whole steel design, the weight of the whole vehicle is light, the garbage load is large, and the fuel is saved, which ensures that the car body is not deformed and has good economy.
3, The optimized design of the medium-pressure transformer hydraulic system has the advantages of fast dynamic response, low heat loss inside the system, high work efficiency, short operation cycle time and simple operation, compared with the high-pressure system with constant pressure throughout the system. Especially reliable work and low failure rate.
4, The design of the central sewage conduit prevents the leakage of sewage and the design of the closed air of the vehicle, completely solving the secondary pollution problems such as running, running, dripping and leaking, thus absolutely avoiding the secondary pollution of the garbage truck during compression loading and transportation.
5, Equipped with an in-cabin operating system for garbage loading, push plate compression and unloading through cab operation.
6, There is a contact buzzer on the front lower side of the cabinet and the cab, through which the operator and the driver can communicate. The “Emergency Stop Device” button next to the tumbling mechanism can stop the operation in time and protect the operator at all times.
Chengli Special Automobile Co., Ltd. is the leading manufacturer and supplier of garbage trucks in China since 2004s. With many years' experience in developing, Chengli Special Automobile Co., Ltd. could supply garbage compactor truck, refuse garbage truck, swing arm garbage truck, skid loader garbage truck, side loader garbage truck, sealed garbage truck, dump garbage truck, etc. More information, please feel free to contact Ms. Anita Deng. The hot sale is 0086 13886878855.